Analyzing the Significant Impacts of Water Infiltration
Originally published by: Building Enclosure — May 3, 2019
The following article was produced and published by the source linked to above, who is solely responsible for its content. SBC Magazine is publishing this story to raise awareness of information publicly available online and does not verify the accuracy of the author’s claims. As a consequence, SBC cannot vouch for the validity of any facts, claims or opinions made in the article.
The ways in which liquid and vapor move through our building envelopes are complex, and even today not completely understood; but the fact that lots of water can (and does) move through porous building materials is a phenomenon that rules over so much of the way we build.
Two major modes of moisture travel—gravity and capillary action—are related to bulk water management, which is essential to the longevity of any building envelope assembly consisting of porous materials.
Two other major modes address how water vapor can work its way through a building envelope assembly. Managing vapor drive is a critical damage function of a building envelope assembly. Building science professionals, designers, and engineers have long debased solutions for managing how vapor may diffuse through an assembly and pose a condensation risk. The bottom line with regard to diffusion is to understand seasonal vapor drive and afford an assembly the opportunity dry. Trapping moisture in an assembly may lead to major problems.
Air infiltration poses a greater condensation risk than diffusion—and it's not even close.
Figure: Quantity of water transmitted through a sheet of gypsum board during a heating season in a cold climate via vapor diffusion and air leakage through a 1-square-inch hole. This figure is adapted from an illustration created by Building Science Corporation. Click to enlarge.
Project teams will pore over issues related to permeance, condensation risks, and strategic placements of vapor retarders in hopes of managing vapor-related moisture issues. However, controlling the flow of air infiltration is far more important than controlling vapor diffusion.
According to a classic analysis by Building Science Corporation, as offered in their Builder's Guide for Cold Climates, during a the heating season in a cold climate region, vapor diffusion through a solid a 4-foot by 8-foot sheet of gypsum board may result in about 0.3 L (1/3 quart) of water being transmitted to the interior. By comparison, the air leakage through a 1-square-inch hole in the middle of the gypsum board over the same period of time may result in approximately 28.4 L (30 quarts) of water being transmitted to the interior—90 times more water than through diffusion.
Infiltration can account for over half of the annual heat exchange through a poorly sealed building envelope; and with that air potentially comes a great amount of vapor. A leaky envelope can undermine even the most optimized vapor diffusion strategy. This underscore the critical need for tight building envelopes as standard practice.
The Continuous Insulation website provides more information on the following topics.
- Importance of Understanding Moisture Vapor Transmission to Prevent Rot
- Video: A Perfect Example of Drying Potential Gone Awry
Perfect Wall Articles
- Creating the ‘Perfect Wall’: Simplifying Water Vapor Retarder Requirements to Control Moisture
- Perfect Walls are Perfect, and Hybrid Walls Perfectly Good
- Wood Framed Wall Insulation Calculator Explained
- New Wall Design Calculator for Commercial Energy Code Compliance
- Energy Code Math Lesson: Why an R-25 Wall is Not Equal to a R-20+5ci
- Continuous Insulation Solves Energy Code Math Problem
- Fear Building Envelopes No More with This Website & Videos
- Thermodynamics Simplified Heat Flows from Warm to Cold
- Moisture Flow Drives Water Induced Problems
- Video: How the 'Perfect Wall' Solves Environmental Diversity
- Video: How Important Is Your WRB?
- Video: A Reliably Perfect Wall Anywhere
- Video: The Best Wall We Know How to Make
- Video: How to Insulate with Steel Studs
- Video: Thermal Bridging and Steel Studs
- Video: Better Residential Energy Performance with Continuous Insulation
- Video: How to (Not) Ruin a Perfectly Good Wall
- Video: Tar Paper and Continuous Insulation? No Problem!
- Video: Do CI and WRBs Go Together?
- Video: Assess Your 'Perfect Wall' Using Control Layers